Image Title Brand Description Price SKU
2A Motor Shield For Arduino

Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This board allows for motor control with Arduino right away. Stack up this shield on your controller and drive motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Compatible Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mounted onto standard Arduino Duemilanove and Arduino Mega.

Speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6. The enable/disable function of the motor control is signalled by Arduino Digital Pin 4 and 7. The Motor shield can be powered directly from Arduino or from external power source. It is strongly encouraged to use external power supply to power the motor shield.

Compatibility :

  • Arduino UNO R3 
  • DFRduino UNO R3
  • Bluno Mega 1280/2560
Rp 217.500 1440019041

A000010 Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 io pins, 6 Analogue inputs, a 16MHz crystal oscillator, a USB connection, a power jack, an ICSP header and a reset button. Uno differs from all preceding boards in that it does not use the FTDI USB to serial driver chip. Instead, it features ATmega16U2 programmed as a USB to serial converter. Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode. Revision 3 of the board has the following new features: 1.0 pin out: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V

Features :
- An open source design
- An easy USB interface
- Very convenient power management and built-in voltage regulation
- 16MHz clock, fast enough for most applications
- 32KB of flash memory for storing the code
- 13 digital pins and 6 Analogue pins
- An On-Board LED attached to digital pin 13 for fast an easy debugging of code
- A button to reset the program on the chip
- ICSP connector for bypassing the USB port and interfacing the Arduino directly as a serial device
- Can be powered via the USB connection or with an external power supply

Rp 839.000 1440019017
Arduino Due

Arduino Due adalah module arduino yang berbasis mikrokontroler Atmel SAM3X8E ARM Cortex-M3 CPU. Arduino Due adalah module Arduino pertama yang menggunakan 32-bit mikrocontroler ARM core. Memiliki 54 digital pin input / output (12 diantaranya dapat digunakan sebagai output PWM), 12 analog input, 4 UART (hardware port serial), frequency Clock 84 MHz, 2 DAC , 2 TWI

Rp 825.000 1440019018
Arduino ETHERNET shield 2 WITH PoE


The Arduino Ethernet is a microcontroller board based on the ATmega328. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz crystal oscillator, a RJ45 connection, a power jack, an ICSP header, and a reset button. 
NB: Pins 10, 11, 12 and 13 are reserved for interfacing with the Ethernet module and should not be used otherwise. This reduces the number of available pins to 9, with 4 available as PWM outputs. 
An optional Power over Ethernet module can be added to the board as well. 
The Ethernet differs from other boards in that it does not have an onboard USB-to-serial driver chip, but has a Wiznet Ethernet interface. This is the same interface found on the Ethernet shield. 
An onboard microSD card reader, which can be used to store files for serving over the network, is accessible through the SD Library. Pin 10 is reserved for the Wiznet interface, SS for the SD card is on Pin 4. 
The 6-pin serial programming header is compatible with the USB Serial adapter and also with the FTDI USB cables or with Sparkfun and Adafruit FTDI-style basic USB-to-serial breakout boards. It features support for automatic reset, allowing sketches to be uploaded without pressing the reset button on the board. When plugged into a USB to Serial adapter, the Arduino Ethernet is powered from the adapter. 

Rp 650.000 1440019016
Arduino Leonardo With Header

Arduino Due adalah module arduino yang berbasis mikrokontroler Atmel ATmega32u4. Memiliki 20 digital input / output (7 diantaranya dapat digunakan sebagai output PWM dan 12 analog input)

Rp 315.000 1440019021
Arduino Mega2560 Rev3-RETAIL

The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.

Rp 715.000 1440019022
Arduino UNO Rev3

Arduino Uno Rev3 merupakan arduino board yang berbasis ATmega328. Arduino uno memiliki 14 digital input/output (6 output dapat digunakan sebagai PWM Output) dan 6 Analog Input.

Rp 335.000 1440019023
Arduino WiFi Shield (integrated antenna)

The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits.

  • Requires an Arduino board (not included)
  • Operating voltage 5V (supplied from the Arduino Board)
  • Arduino Due compatible
  • Connection via: 802.11b/g networks
  • Encryption types: WEP and WPA2 Personal
  • Connection with Arduino on SPI port
  • on-board micro SD slot
  • ICSP headers
  • FTDI connection for serial debugging of WiFi shield
  • Mini-USB for updating WiFi shield firmware
Rp 1.500.000 1440019020
Arduino Yun

Arduino Yun merupakan arduino board yang berbasis ATmega32U4 dan Atheros AR9331. Pada module ini Terdapat ethernet port dan WiFi. Memiliki micro-SD slot, 20 Digital Input/output (7 buah output dapat difungsikan sebagai PWM, 12 buah dapat difungsikan sebagai analog input)

Rp 1.195.000 1440019019
Relay Shield for Arduino V2.1

One of the most interesting projects for your boards is perhaps being able to control High power devices like Lamps, water pumps, garage doors and so on. But interfacing with high power and AC is quite a dangerous task when building the circuitry. Relays allow for interfacing an external electrical circuit like a switch. With relays you can now connect external circuit or devices directly to your Arduino.

DFRobot Relay Shield V2.1 is a completely new design which is capable of controlling 4 relays at a time. The max switching power DC 90W or AC 360VA gives direct control by Arduino/DFRduino controllers through digital I/Os with external 9V supply. With built-in Xbee socket, it can be wireless remote controlled via Xbee/bluetooth/WPM.

This relay shield is an ideal solution for home automation and robotics purposes.

NOTE:It requires an external power supply to drive the xbee module and relays.

Rp 227.500 1440019035